Get the latest Flash player
Just Doors offers a hassle free alternative to dealing with the large home improvement stores and expensive general contractors for replacement doors. After years of installing doors for those home improvement stores we have observed the problems customers encounter and have tried to eliminate them. We feel that because the only thing we do is doors, we can offer experience above and beyond any general contractor or handyman.
This company was formed on the basis of providing quality workmanship with a personal touch. We strive to provide our customers with excellent service by friendly people. So feel free to give us a call or contact us on the website and let us share our knowledge and experience with you. Thanks for choosing JUST DOORS, we look forward to working with you on you next door project.
Deadbolt Lock Installation - Drilling and Chiselling the Door
Home Improvement Expert Ryan Arensdorf demonstrates the first step of deadbolt lock installation, drilling and chiselling the door.
This series: 60,480 views
Ryan Arensdorf: Hi! I am Ryan with Just Doors. Today, we are going to be talking about installing a deadbolt. Now most doors, if you purchase a new one, will come with a hole drilled in it. However, if you don't have a hole, we are going to show you what you need to do to prep the door marked for the holes and drill out for the deadbolt itself.
Now if your door comes bored with holes already, you can go ahead and skip to the next clip. This door doesn't have a hole in it for the handle. So we will be marking 36 up from the bottom of the door and then 5 up from there for the proper deadbolt location. Now we will use a Speed Square to mark where our holes are on each side of the door. We will mark the other side as well. This particular hole will be marked at 2 3/8 to accommodate the backset. When figuring out the location for the backset, determine if you are going to do a 2 3/8 or 2 3/4 inch. Most of the new deadbolts that you will purchase from any home store will be adjustable for 2 3/8 and 2 3/4. Because we don't have a hole drilled, we can set the backset up. Now that we have got our holes marked, we are ready to drill for the deadbolt. Now we will be using our 1-8th drill bit to mark pilot holes where our center line is on our door. Now we will move to the other side, find a mark, drill about 1/4 inch to 1/2 inch in. Just give it a double check it for accuracy, 2 3/8. Now we will switch for 2-1/8 hole saw and begin drilling.
Drill about half way through the door, move to the other side and finish all the way through. It's important to keep the drill level and plum when you are drilling through the hole. You will also want to find the center of the hole for the backset. This is 1-3/4 door, so we will mark our center at 7/8. Now we are using a 1 inch spade bit to drill for backset. Again, it's important to keep this very straight going into the holes, so that you don't mess up either side of the door. Now that our holes are drilled, we are ready to mark and chisel for the backset. Just mark all four sides, so you know where to chisel. Now that we are marked for the deadbolt, we are ready to chisel. I'll be using a 1 inch chisel for this. It's a good idea to start from the top and bottom as a backset should be somewhere around 1 inch. Hammer the chisel in, approximately in just 3/16th.
Be careful when drilling the sides that you don't go too deep and chip off the edge of the door. Set the chisel back about 1/8th of an inch, trying to keep it as flat as possible when you are hammering it. Chisel out through an approximate depth of 1/8th inch to 1/4 inch. Use the backset to check that it's flush with the edge of the door. Now that the holes are drilled and the backset is chiseled out, we are ready to install the backset and deadbolt. Up next, we are going to be showing you how to install the deadbolt.